Moreover, how do I reset the OBC on my EZ Go golf cart?
- Key switch to off.
- Set forward/reverse to neutral.
- Put tow/run switch to tow.
- Disconnect the negative battery terminal from the battery pack.
- Put the tow/run switch to run.
- Put forward/reverse switch to reverse.
- Put key switch to on.
In this regard, how do you remove the speed limiter on a electric golf cart?
Subsequently, how do I remove club car from OBC?
Furthermore, how do you bypass a golf cart controller?
The OBC is a small device that is wired into the golf cart that’s purpose is to regulate the batteries charge. As you use and drive your golf cart, the OBC records the amount of energy consumed and then directs the charger to replace exactly the amount of energy needed to fully replenish the batteries.How do I reset my electric golf cart motor?
First, you’ll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again.
How can I make my golf cart governor faster?
If you find this rod, then your governor can be easily adjusted by accessing the cart’s inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart’s governance to increase the overall speed.
How do you take the governor off an electric golf cart?
How do you turn off a speed regulator on a golf cart?
Look behind the governor to find a small metal rod that’s permanently attached to the club car and stretch your rubber band enough to connect it to that metal rod. Screw the plastic plate back in place. Once the plate is back in place, the governor is disabled.
How do you bypass OBC on a 2000 Club Car DS so it will charge?
To bypass the OBC you will need to connect a 12 gauge black wire from the negative terminal of this battery to where the black wire attaches to the back of the receptacle. That’s it folks; you’re done!
Does my golf cart have an OBC?
Look for the main negative wire coming off of the last battery in sequence(it will be the only negative wire not going to another battery). If you have an OBC(on board computer) the wire will come off of that negative wire and through the middle of a small box about 4″ inches square. The small box is the OBC.
How do you bypass the charger on a club car?
How do you bypass a controller?
What is the OBC on a club car?
Club Car uses an On Board Computer (or OBC) to monitor and control various functions of their carts. It functions as a Go/No Go control for the charging and drive systems. If the OBC detects a problem in either the charging or drive system, it will shut that feature off.
How do you start a golf cart without a key?
How do I check my club car OBC?
- Set the voltage meter to DC Volts 200V.
- Take voltage from the positive side of the charger port/receptacle to the negative on the battery pack loop of batteries.
- There should be voltage read on the battery back, this may vary based on the charge.
Where is the motor reset button on a club car?
Expose the motor (you’ll probably need a screwdriver to remove the cover), and look for a red button. It is usually near the main power source, where most of the wires are connected. Once you’ve pressed the button to reset the motor, reassemble the cart, charge up the batteries, and give it a test run.
Do all golf carts have a reset button?
Electric golf cart motors have a reset button on their chassis which is designed to put your motor back into its original factory state.
How do you bypass a solenoid on a golf cart?
Bypassing Golf Cart Solenoid Method If you do decide to bypass the solenoid, this is what you need to do: Take the two larger wires that connect to the solenoid and connect them directly (keeping all safety precautions in place). This should do the trick and if it does not work then the solenoid is not the problem.
Where is the reset button on a golf cart?
Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
